Boondocker POLARIS: Non-turbo Control Box 2011-12 PRO RMK 800 User Manual download pdf (Page 8)

BoonDocker Performance – 2379 Heyrend Way, Idaho Falls, ID 83402 – 208-542-4411 / 877-522-7805

www.boondockers.com – email: info@boondockers.com – fax: 208-524-7381

These maximum values will be saved when the box is shut off so they will remain the next time this screen is

displayed even if the box is re-powered. Peak values or “spikes” are filtered by finding the average during a certain

time-window. Therefore, a maximum must be held for at least 1 second to be recorded and displayed properly.

Use the arrow keys to move the cursor between Y and N. Pressing SEL when the cursor is on Y will clear the max

values. Pressing SEL when the cursor is on N takes you to the next screen: Stats: N2O/DC.

5.3 Stats: N2O/TPS

This menu displays nitrous information.

N2O PSI MxTP Clr.

32 240 208 YN.

N2O 32 Maximum fuel adjustment during last nitrous activation (blacked out █ █ █ during

nitrous activation). This can be cleared manually and is always clear upon next nitrous

activation.

PSI 240 For systems without a N2O pressure regulator (NON in lower right-hand corner of

Startup Screen), this displays current nitrous tank pressure. For systems using a N2O

pressure regulator (ADJ or FIX in lower right-hand corner of Startup Screen), this

shows the maximum nitrous pressure during the shot, where the pressure is measured

after the solenoid valve. The maximum is averaged over a 1 second period.

MxTP 208 Maximum throttle position reading since this menu was last cleared or since engine

was last started.

Selecting Y will clear these values. Use any arrow key to select Y or N. Pressing “SEL” takes you to the Main Menu.

VI. N2O System Configuration

A. N2O Configuration Options

There are seven ways to configure nitrous activation using one or more of the following inputs: button, throttle position,

and rpm range. A brief description for each configuration is given below. Detailed setup instructions are provided in

sections B and C.

1. Button only: Pressing the momentary button on the handlebar activates the nitrous and releasing the button turns

it off. TPS and RPM are ignored.

2. TPS (Throttle Position Sensor) only: When the throttle is pressed beyond a point set by the user, nitrous is

activated. Nitrous is deactivated when the throttle returns to a point below the chosen threshold.

3. TPS and RPM: When the RPM and TPS are within a range set by the user, nitrous will activate. Nitrous will

turn off when the throttle is decreased (TPS is below the adjustable threshold) or when the RPM is out of the

selected range (lower than Min or higher than Max).

4. Button (N2O) or TPS: The handlebar button can be used in combination with the TPS. In this way, either the

throttle or the button can activate the nitrous. The button will always activate nitrous regardless of the TPS

condition.

5. Button (N2O) or TPS and RPM: The handlebar button can be used in combination with the TPS and RPM

range. In this way, either the throttle/RPM or the button can activate the nitrous. The button will always activate

nitrous regardless of the TPS and RPM conditions.

6. Button (ARM) and TPS: The nitrous button input on the Control Box can be used to quickly arm and disarm

nitrous capability. When armed (button input is on), the system can be configured to activate with TPS.

Optionally, the handlebar button, which is momentary (only activated while pressed), can be replaced with a

toggle, rocker, or slide switch so it remains in the on or off position as desired.

7. Button (ARM) and TPS and RPM: Same as option 6 above except with RPM capability. When armed (button

input is on), the system can be configured to activate with TPS and RPM.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 16 17

Comments to this Manuals

No comments

Boondocker POLARIS: Non-turbo Control Box 2011-12 PRO RMK 800 User Manual Page 8

Comments to this Manuals

Related products and manuals for Air equipment Boondocker POLARIS: Non-turbo Control Box 2011-12 PRO RMK 800